hey its me again i was just wondering if you got them in again. its been a while since i have talked to you so i just wanted to check up on their status
show more
I'll see if I can do colour choice. No confirmation yet.
Lol I hate region locked stuff.
I know right!? I have heard that putting a towel or cloth over it helps. I don't really understand how, but I tried it and it helps a little so you don't have to use the force that you would use to cut the branch off of a tree with an ax XD.
Cases.... fortnight? I don't have a 3D printer so there's a lot of shuffling getting other people to print them for me.
Would you make your 3D models available for people printing their own cases? In that case, I think I could ask a friend of mine to print it for me
Looking foward to get one, even if it will take a while
Another new idea since they come in parts , why not offer multicolor ones?
Awesome! I'll put in my order when I get home from work~
Here's the guide I used: http://www.neogaf.com/forum/showpost.ph ... tcount=117
This cork plate worked without needing any modifications: https://www.amazon.com/gp/product/B0000 ... UTF8&psc=1
For steps 9-10, I couldn't get a 5 mm hole puncher, so I stuffed the holes with tissue and put tape over the holes. I also stuffed some tissues into the empty area shown in step 3 to lessen the impact from hits.
You might have to do some more modifications after testing (some of the rubber would make the kat parts too sensitive on mine, so I had to cut those pieces of rubber off), but if you're willing to do that, the results are very noticeable.
On another note, I haven't gotten my converter yet, but I can't wait to use it. I might make a video on it if I can properly record it and show the improvement in delay.
i already have a recording from today if you want to see the no delay https://twitch.tv/deconstream/v/80370278
Now it's time to figure out how spinners and bouncing works, eh?
I'm assuming you're using the guide from above; can I ask how much the mod cost you and where you bought everything from?
this was mainly just to show how responsive the drum itself was. i haven't modified any of the sensors for the rims yet. well i did, but i screwed them up so i reverted back to normal and i'll try them again tomorrow.
i used the exact guide you linked. the cork things cost me $7.99 for three + shipping, i managed to get some scrap rubber for free at home depot, and the rest of my shopping was buying a mini hole punch and some tape which probably cost me $3 total. it wasn't too bad at all, and the mod itself probably took me 2 hours. filling all of the holes with rubber takes more time than you'd think, plus i didn't really know exactly what i was doing.
just a warning, if you mod like this, you can't overlap the left and right side rim sensors with the rubber or both sides will be treated the same which can cause some problems. i also noticed there's a spot right in the middle of my drum that hits both dons at the same time, but that's super minor.
once i can perfect the sensors on the rims i'll update and let you know how it goes c:
Look forward to the update!
show more
Topic Starter
Still waiting on them to ship. Chinese New Year slowed things down somewhat, combined with the extended delay in sourcing parts.AnimeGod2205 wrote:
hey its me again i was just wondering if you got them in again. its been a while since i have talked to you so i just wanted to check up on their status
Dang, they havent even shipped yet? so many delaysmontymintypie wrote:
Still waiting on them to ship. Chinese New Year slowed things down somewhat, combined with the extended delay in sourcing parts.AnimeGod2205 wrote:
hey its me again i was just wondering if you got them in again. its been a while since i have talked to you so i just wanted to check up on their status
Ahh this is the converter of my dreams. 100% Confirmed for one once they get in!
Topic Starter
Great news! They've finally shipped to me! Expect them to be here in 2 weeks
Topic Starter
Still waiting for the parcel, but while I wait, I got hard numbers on latency.
Using my scope, I had 1 probe connected to a piezo mic, and another to the LED of the converter. This LED updates at 1KHz, the same rate as the USB update rate.
I then smacked the drum 50 times, and recorded the delay between the moment the piezo started to respond, and when the converter registered a hit. An example measurement:
After 50 hits, here are the results:
Average: 1.802ms
Median: 1.77ms
Std Deviation: 0.44454517
Min: 1.1ms
Max: 2.78ms
Rounding the max value up, I can confidently say that there is an absolute worst case 3ms lag. And average lag of 1.8ms. This is imperceptible. Lagfree = confirmed!
Using my scope, I had 1 probe connected to a piezo mic, and another to the LED of the converter. This LED updates at 1KHz, the same rate as the USB update rate.
I then smacked the drum 50 times, and recorded the delay between the moment the piezo started to respond, and when the converter registered a hit. An example measurement:
After 50 hits, here are the results:
Average: 1.802ms
Median: 1.77ms
Std Deviation: 0.44454517
Min: 1.1ms
Max: 2.78ms
Rounding the max value up, I can confidently say that there is an absolute worst case 3ms lag. And average lag of 1.8ms. This is imperceptible. Lagfree = confirmed!
Topic Starter
I've been prototyping a case.
This is an early prototype so the case doesn't fit properly and looks bad, but would there be interest? It would be 3-5 USD delivered, or cheaper if bundled with the converter. The source is also open so if you own a 3D printer you can make it yourself.
Pictures inside the spoilerbox...
This is an early prototype so the case doesn't fit properly and looks bad, but would there be interest? It would be 3-5 USD delivered, or cheaper if bundled with the converter. The source is also open so if you own a 3D printer you can make it yourself.
Pictures inside the spoilerbox...
I'd like a case when I buy one yeah, would be nice.
I'm happy that I was able to help you and give you the thought of doing cases for them. Given any thought to making them in different colors?
Topic Starter
Any colour, so long as it's black...AnimeGod2205 wrote:
Given any thought to making them in different colors?
I'll see if I can do colour choice. No confirmation yet.
Haha okmontymintypie wrote:
Any colour, so long as it's black...AnimeGod2205 wrote:
Given any thought to making them in different colors?
I'll see if I can do colour choice. No confirmation yet.
Can't wait till I can get my hands on this. Got a taiko game for Wii for Christmas two years back and couldn't play it since the game is region locked.
Obama Taichou wrote:
Can't wait till I can get my hands on this. Got a taiko game for Wii for Christmas two years back and couldn't play it since the game is region locked.
Lol I hate region locked stuff.
yes sirAnimeGod2205 wrote:
Lol i hate region locked stuffObama Taichou wrote:
Can't wait till I can get my hands on this. Got a taiko game for Wii for Christmas two years back and couldn't play it since the game is region locked.
Great news!
Will you ship it to Brazil when it's available?
Will you ship it to Brazil when it's available?
Topic Starter
I hear that in Brazil post can take a very long time. I will ship there, but can make the package Registered if you require the additional guarantee.afureru wrote:
Will you ship it to Brazil when it's available?
This looks SO amazing! I'd love to use this for Taikojiro, actually. Would it only work with Osu?
//also if possible could I be emailed when they arrive? I don't wanna miss them or anything :3
//also if possible could I be emailed when they arrive? I don't wanna miss them or anything :3
Topic Starter
The converter pretends to be a keyboard - as long as the keys are set to the same ones you use in Taikojiro, it will work fine. I will release the configuration app when I start shipping converters.
If you subscribe to this thread you will get an email when someone posts. I will post as soon as they arrive! I expect them here by Friday - fingers crossed
If you subscribe to this thread you will get an email when someone posts. I will post as soon as they arrive! I expect them here by Friday - fingers crossed
I just recently got a tatacon and when I Bluetooth connected it to my PC, it worked on osu but I had to hit ACTUAL SMASHING strength to get just one hit and I think it's the problem with the wii so I am really looking forward to this. I also admire you on how you have been working on this for a year!!
So when do you think the final product will be ready and ready to ship, I really need this!
So when do you think the final product will be ready and ready to ship, I really need this!
FluffyHuggie wrote:
I just recently got a tatacon and when I Bluetooth connected it to my PC, it worked on osu but I had to hit ACTUAL SMASHING strength to get just one hit and I think it's the problem with the wii so I am really looking forward to this. I also admire you on how you have been working on this for a year!!
So when do you think the final product will be ready and ready to ship, I really need this!
I know right!? I have heard that putting a towel or cloth over it helps. I don't really understand how, but I tried it and it helps a little so you don't have to use the force that you would use to cut the branch off of a tree with an ax XD.
Topic Starter
They're here!
Building...
Complete!
2 important notes
While you're at it, the Chrome web app is now public. You will need it to configure buttons, LEDs, debouncing, and for future firmware updates.
Building...
Complete!
2 important notes
- The cases aren't ready yet. If you purchase now you won't get a case.
I underestimated some costs and the price had to be raised to $25. Shipping is still free!
While you're at it, the Chrome web app is now public. You will need it to configure buttons, LEDs, debouncing, and for future firmware updates.
Ahhhh, yissss! I been creeping on this thread for ages! My order has been made!
heck, i've only got 20$ :// next time for sure! ^^
Ordered mine, looking forward to it!
I'll pass on this first batch actually because I can't use it right now, but I'm looking forward to see footage of people playing and using one, that would be pretty cool!
Ill be waiting for the cases to come out so when will that be, and also how much stock do you have because I surely wouldn't want it to run out and I won't be able to buy it! 
Topic Starter
I have 12 left. If I run out, I will simply order moreFluffyHuggie wrote:
Ill be waiting for the cases to come out so when will that be, and also how much stock do you have because I surely wouldn't want it to run out and I won't be able to buy it!
Cases.... fortnight? I don't have a 3D printer so there's a lot of shuffling getting other people to print them for me.
Alright then I'll be waiting to order it when you announce the cases thanks!montymintypie wrote:
I have 12 left. If I run out, I will simply order moreFluffyHuggie wrote:
Ill be waiting for the cases to come out so when will that be, and also how much stock do you have because I surely wouldn't want it to run out and I won't be able to buy it!
Cases.... fortnight? I don't have a 3D printer so there's a lot of shuffling getting other people to print them for me.
I also was insterested on your case, but I'm afraid you run out of converters by the time you get them ready...FluffyHuggie wrote:
I have 12 left. If I run out, I will simply order moremontymintypie wrote:
Ill be waiting for the cases to come out so when will that be, and also how much stock do you have because I surely wouldn't want it to run out and I won't be able to buy it!
Cases.... fortnight? I don't have a 3D printer so there's a lot of shuffling getting other people to print them for me.
Would you make your 3D models available for people printing their own cases? In that case, I think I could ask a friend of mine to print it for me
Topic Starter
Absolutely! The unfinished cases are in .scad format in the Github repo. When they are finished, I'll also release .stl files which any 3D printer supports!afureru wrote:
Would you make your 3D models available for people printing their own cases? In that case, I think I could ask a friend of mine to print it for me
Oh and if you have time can you show us a example like a video or something that shows the usb converter and a tatacon in use so I could see the lag free results and just how hard or soft you need to hit, but you dont have to I'm just curious
Topic Starter
Give me a couple of days to clean my desk and sureFluffyHuggie wrote:
Oh and if you have time can you show us a example like a video or something that shows the usb converter and a tatacon in use so I could see the lag free results and just how hard or soft you need to hit, but you dont have to I'm just curious
ALRIGHT heheh
OMG!
Definitely buying one in the near future!
Great work, montymintypie!
Definitely buying one in the near future!
Great work, montymintypie!
Topic Starter
I'm about to order more boards, but I wanted to ask people's opinions - currently there's a USB A port on the converter. It's like a USB flash drive or a dongle of sorts.
Would people prefer micro USB, like on their phone? Pros: can get a longer cable out of it. Cons: If you don't have a cable already it's 1 extra thing you need.
Would people prefer micro USB, like on their phone? Pros: can get a longer cable out of it. Cons: If you don't have a cable already it's 1 extra thing you need.
I would want it to be just the USB for computer, more easier just plug it in right away right?montymintypie wrote:
I'm about to order more boards, but I wanted to ask people's opinions - currently there's a USB A port on the converter. It's like a USB flash drive or a dongle of sorts.
Would people prefer micro USB, like on their phone? Pros: can get a longer cable out of it. Cons: If you don't have a cable already it's 1 extra thing you need.
Topic Starter
I have just ordered 50 more boards, same style as the first batch. I estimate 1.5 months delivery. Hopefully they don't have component supply issues again!
Still working on the cases - 3D printing comes with its own set of challenges.
I have about 5 boards left from the first batch.
Still working on the cases - 3D printing comes with its own set of challenges.
I have about 5 boards left from the first batch.
My converter just came in today! Will test out and see if it's worthwhile.
Got mine in the mail just now, unfortunately my drum decided to stop functioning this morning... so I have no way of testing it at this time 
if anyone has a spare one that I can borrow, I would be very grateful. I was planning on doing a series of videos.
Edit: the Aussie candies were a nice touch.
if anyone has a spare one that I can borrow, I would be very grateful. I was planning on doing a series of videos.Edit: the Aussie candies were a nice touch.
Wow they look amazing (OCD is satisfied that they are all aligned)
Topic Starter
Thanks for everyone's support! The first batch is now sold out.
I expect the second batch by late April/early May. By then I should hopefully have nailed the case design too. People who have purchased this batch will be able to 3D print their own case
I expect the second batch by late April/early May. By then I should hopefully have nailed the case design too. People who have purchased this batch will be able to 3D print their own case
Do you still have mine on hold? It's fine if you don't I can wait until the next batch but I will be able to buy it this weekend(Hopefully).montymintypie wrote:
Thanks for everyone's support! The first batch is now sold out.
I expect the second batch by late April/early May. By then I should hopefully have nailed the case design too. People who have purchased this batch will be able to 3D print their own case
Topic Starter
Yes! I wouldn't sell it after holding it so long, that'd just be rude.AnimeGod2205 wrote:
Do you still have mine on hold?
Thanks!montymintypie wrote:
Yes! I wouldn't sell it after holding it so long, that'd just be rude.AnimeGod2205 wrote:
Do you still have mine on hold?
Anyone who needs one before May can pm me. I can't really afford a new drum with a baby on the way... $25 shipped. US buyers only.
Ah! Mine came today! (I hadn't said earlier, but I had scrapped up enough money to buy one! ;3) I can't test it now since i'm actually still remodeling my drum, but I can do it later. I can update then! Thanks so much @montymintypie!! ! (For the little gifts too :33)
EDIT: I had finished fixing my drum, and i've gotta say, this works wonders! I love it so much. There's no delay at all for me. I can now play songs that are not on TnT Wii with a tatacon, and effectively! Thank you again!! :3!
! (For the little gifts too :33)EDIT: I had finished fixing my drum, and i've gotta say, this works wonders! I love it so much. There's no delay at all for me. I can now play songs that are not on TnT Wii with a tatacon, and effectively! Thank you again!! :3!
Topic Starter
Excellent to hear @MakkipMaster
New updates - I bought a 3D printer. Delivery sometime next week. If all goes well, this means I can add cases to all future converters for no extra cost
New updates - I bought a 3D printer. Delivery sometime next week. If all goes well, this means I can add cases to all future converters for no extra cost
Woohoo finally got mine. It looks amazing. Works perfectly! I love the LED's. Great job. I was wondering if you could send me a 3d printed shell that I could add to it? I'd be willing to pay extra for it.
Topic Starter
Super duper easy. Completely plug and play, with the Chrome app to change the key bindings.
3D printing is hard and the next batch is still being produced. Thank you all for your patience.
3D printing is hard and the next batch is still being produced. Thank you all for your patience.
Yes it is! You simply plu in the tatacon to the device, then plug the device in to your computers usb slot. Simple as that!Loc wrote:
I´ve been thinking for a while to use a tatacon, is it easy to install this?
Hey awesome project monty. I had bought a tatacon and all the wii crap a while back but once i got osu open I found myself drowning in lag ;-;
poor tatacon has been sitting in the closet for months now thanks to that. I wish i had known about your project beforehand. Do you have that next batch(with cases) finished yet? I'd love to have a converter.
poor tatacon has been sitting in the closet for months now thanks to that. I wish i had known about your project beforehand. Do you have that next batch(with cases) finished yet? I'd love to have a converter.
Topic Starter
Still waiting - will email to determine the production delay. Cases are improving and almost readyChry wrote:
Do you have that next batch(with cases) finished yet? I'd love to have a converter.
Topic Starter
Received information from supplier:
-PCB has been ready.Thus new estimate is Mid June for more stock
-All of materials will be got on May 23.
-PCBA assembly will be started on May 24.
-The goods will be shipped on May 25.
Would be awesome, if that works...
Thinking about getting a tatacon drum maybe.
Thinking about getting a tatacon drum maybe.
Topic Starter
To all those following, thanks again for the patience
If you're thinking of buying one, could you fill this survey on case colour? I'll be able to offer white, black, blue and red and would like to know roughly how much to print of each. If there's big demand for another colour I will buy more filament.
PCBs have shipped and I should receive them within 2 weeks. It may take a bit longer to start shipping since that'll coincide with my exams for this semester. But almost there
If you're thinking of buying one, could you fill this survey on case colour? I'll be able to offer white, black, blue and red and would like to know roughly how much to print of each. If there's big demand for another colour I will buy more filament.
PCBs have shipped and I should receive them within 2 weeks. It may take a bit longer to start shipping since that'll coincide with my exams for this semester. But almost there
Done.montymintypie wrote:
could you fill this survey on case colour?
Looking foward to get one, even if it will take a while
First of all, hi to the community. Noob here. Made an account just to write in this thread and discovered Osu! on the way
I wanted to congratulate montymintypie for such awesome board, one of the coolest I've seen in my life and this comes from someone with several Cave PCBs at home. I wanted to buy a couple of boards with blue and red boxes although my daughter would prefer pink I'll be checking for updates. Keep up the good work!
I wanted to congratulate montymintypie for such awesome board, one of the coolest I've seen in my life and this comes from someone with several Cave PCBs at home. I wanted to buy a couple of boards with blue and red boxes although my daughter would prefer pink
I'll be checking for updates. Keep up the good work!Just wondering, when the first post said to expect a resupply this June, is that recent (2016)? Does it work with cheap knockoff Tatacons? And does osu! automatically detect it when plugged in? And will this batch have cases?
Topic Starter
Yes, this June 2016! This parcel is taking its time to arrive at my house...
I own both genuine and knockoff, works on both. Even works on the very expensive Hori controllers.
Osu doesn't need to detect the drum as it pretends to be a keyboard. However I do like navigating songs with the drum, expect that to come to osu when it becomes open source.
Yes to cases for this batch - printer is ready!
I own both genuine and knockoff, works on both. Even works on the very expensive Hori controllers.
Osu doesn't need to detect the drum as it pretends to be a keyboard. However I do like navigating songs with the drum, expect that to come to osu when it becomes open source.
Yes to cases for this batch - printer is ready!
Topic Starter
Topic Starter
Thoughts as I finalise cases - what option would people prefer?
- Cases are glued and cannot be taken apart without snapping. Stronger.
Cases are clipped and look a little worse, but can be taken apart if you want.
Just got into Taiko and am interested in this.
I probably wouldn't mod it, so I would prefer the glued version.
I probably wouldn't mod it, so I would prefer the glued version.
If the case is strong enough with clipped parts, i'd say you can go for clipped.
I dont mind if its glue or clipped for my reasons
I dont mind if its glue or clipped for my reasons
Topic Starter
Status update:
Cases will be strong and hold the board very well without the need for glue.
I have gone through many prototypes:
The cases for the old and new versions are on Thingiverse now.
Almost ready, but I am fixing some print quality issues. I want to make sure people receive the best quality product.
Cases will be strong and hold the board very well without the need for glue.
I have gone through many prototypes:
The cases for the old and new versions are on Thingiverse now.
Almost ready, but I am fixing some print quality issues. I want to make sure people receive the best quality product.
Thanks again for making these available!montymintypie wrote:
Status update:
Cases will be strong and hold the board very well without the need for glue.
I have gone through many prototypes:
The cases for the old and new versions are on Thingiverse now.
Almost ready, but I am fixing some print quality issues. I want to make sure people receive the best quality product.
the cases look really nice! i already forgot which color i put down for myself when i submitted the form but i just want to say that i'm still really excited for these!
so whats the status for now? when are they going to be available?
They should be in stock very soon from what ive seen. Also this is for monty, i had a suggestion for a new color, the official osu! Shade of pink. I think it would be pretty nice to have that as a color option.mizuki-chan wrote:
so whats the status for now? when are they going to be available?
Topic Starter
Mere days away (for real this time!). I've finally got the quality up to scratch, the solution is to just print everything really slowly. I'm printing ~8 of each colour so I actually have stock to sell when I open orders. It's about 10 hours of printing so including breaks, 2 days absolute tops. Prepare your wallets
Have also ordered the next 50 PCBs. Stock issues should subside
You're making me broke. Purchased 3 new rolls - osu! pink, silver and lime green.AnimeGod2205 wrote:
i had a suggestion for a new color, the official osu! Shade of pink. I think it would be pretty nice to have that as a color option.
Have also ordered the next 50 PCBs. Stock issues should subside
Haha, I'm sorry. Thats awesome. Those are really god collors and i think that the osu! Pinkwill sel very well(i'm jellous cause i want a silver but ill just print it myself haha)montymintypie wrote:
Mere days away (for real this time!). I've finally got the quality up to scratch, the solution is to just print everything really slowly. I'm printing ~8 of each colour so I actually have stock to sell when I open orders. It's about 10 hours of printing so including breaks, 2 days absolute tops. Prepare your walletsYou're making me broke. Purchased 3 new rolls - osu! pink, silver and lime green.AnimeGod2205 wrote:
i had a suggestion for a new color, the official osu! Shade of pink. I think it would be pretty nice to have that as a color option.
Have also ordered the next 50 PCBs. Stock issues should subside
Another new idea since they come in parts , why not offer multicolor ones?
Topic Starter
Thank you everyone again for your patience. They are on sale again!
Check the first post for more info, or just click here
Check the first post for more info, or just click here
The rear cover is far too small for me to make it an official option, but if someone wants to mix and match, just leave a note when you purchase.AnimeGod2205 wrote:
Another new idea since they come in parts , why not offer multicolor ones?
montymintypie wrote:
Thank you everyone again for your patience. They are on sale again!
Awesome! I'll put in my order when I get home from work~
Topic Starter
New colours now available - pink, silver and lime green
Dannnggggg those look nice. Any chance of a limited transparen edition? Hahamontymintypie wrote:
New colours now available - pink, silver and lime green
I totally would go for a transparent one, especially since they used to have a face on the board. But I was impatient and bought a white one as soon as they came out.
My tatacon just arrived in the mail, and after hours of butthurt trying to pair my Wiimote I got it to work. I note in the product features that it's so sensitive you can bounce your sticks for multihits; trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit. Is the converter more sensitive than the Wiimote, or is it a hardware thing? Because I really don't want to get noise complaints from my neighbors, during the night it sounds as loud as a real drum.
My tatacon just arrived in the mail, and after hours of butthurt trying to pair my Wiimote I got it to work. I note in the product features that it's so sensitive you can bounce your sticks for multihits; trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit. Is the converter more sensitive than the Wiimote, or is it a hardware thing? Because I really don't want to get noise complaints from my neighbors, during the night it sounds as loud as a real drum.
It can be heard throughout a household but not by neighbors. I ordered mine when it first came out which would be nice to get a clear case for.ToaKarn wrote:
I totally would go for a transparent one, especially since they used to have a face on the board. But I was impatient and bought a white one as soon as they came out.
My tatacon just arrived in the mail, and after hours of butthurt trying to pair my Wiimote I got it to work. I note in the product features that it's so sensitive you can bounce your sticks for multihits; trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit. Is the converter more sensitive than the Wiimote, or is it a hardware thing? Because I really don't want to get noise complaints from my neighbors, during the night it sounds as loud as a real drum.
well my converter came in today, i will say the 0 delay claim is true and it's really fun to use! still trying to get used to how to actually control the drumsticks and hit the correct part of the drum, i find myself often hitting a dead part of the drum when i try to hit kats c:
i think my drum is just trash though because it's having a lot of trouble registering even the most basic hits. i messed around with debouncing settings and stuff, and nothing seemed to make any difference. the drum was new and it's the same one that comes with taiko wii games, but i can't really test the drum on its own without the game.
regardless, after a 2+ hour session playing random maps to test it out, i have to say it's a lot of fun! i'll definitely do some more testing to confirm it's just the drum having problems and not the converter c:
i think my drum is just trash though because it's having a lot of trouble registering even the most basic hits. i messed around with debouncing settings and stuff, and nothing seemed to make any difference. the drum was new and it's the same one that comes with taiko wii games, but i can't really test the drum on its own without the game.
regardless, after a 2+ hour session playing random maps to test it out, i have to say it's a lot of fun! i'll definitely do some more testing to confirm it's just the drum having problems and not the converter c:
ToaKarn wrote:
trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit.
That's just how the normal tatacon is. Luckily, there are some mods you can do that will make it work better.Catgirl wrote:
i think my drum is just trash though because it's having a lot of trouble registering even the most basic hits.
Here's the guide I used: http://www.neogaf.com/forum/showpost.ph ... tcount=117
This cork plate worked without needing any modifications: https://www.amazon.com/gp/product/B0000 ... UTF8&psc=1
For steps 9-10, I couldn't get a 5 mm hole puncher, so I stuffed the holes with tissue and put tape over the holes. I also stuffed some tissues into the empty area shown in step 3 to lessen the impact from hits.
You might have to do some more modifications after testing (some of the rubber would make the kat parts too sensitive on mine, so I had to cut those pieces of rubber off), but if you're willing to do that, the results are very noticeable.
On another note, I haven't gotten my converter yet, but I can't wait to use it. I might make a video on it if I can properly record it and show the improvement in delay.
yeah i've had people suggest i mod it, i'll definitely take a look c:GMMAwesome wrote:
ToaKarn wrote:
trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit.That's just how the normal tatacon is. Luckily, there are some mods you can do that will make it work better.Catgirl wrote:
i think my drum is just trash though because it's having a lot of trouble registering even the most basic hits.
Here's the guide I used: http://www.neogaf.com/forum/showpost.ph ... tcount=117
This cork plate worked without needing any modifications: https://www.amazon.com/gp/product/B0000 ... UTF8&psc=1
For steps 9-10, I couldn't get a 5 mm hole puncher, so I stuffed the holes with tissue and put tape over the holes. I also stuffed some tissues into the empty area shown in step 3 to lessen the impact from hits.
You might have to do some more modifications after testing (some of the rubber would make the kat parts too sensitive on mine, so I had to cut those pieces of rubber off), but if you're willing to do that, the results are very noticeable.
On another note, I haven't gotten my converter yet, but I can't wait to use it. I might make a video on it if I can properly record it and show the improvement in delay.
i already have a recording from today if you want to see the no delay https://twitch.tv/deconstream/v/80370278
You mean I have to spend even more money on this? ;_; I'll take a look into this when I have an actual income and soundproofing on my walls, thanks!GMMAwesome wrote:
ToaKarn wrote:
trying out the tatacon, though, I noticed it takes a good amount of force whacking it to get a hit.That's just how the normal tatacon is. Luckily, there are some mods you can do that will make it work better.Catgirl wrote:
i think my drum is just trash though because it's having a lot of trouble registering even the most basic hits.
Here's the guide I used: http://www.neogaf.com/forum/showpost.ph ... tcount=117
This cork plate worked without needing any modifications: https://www.amazon.com/gp/product/B0000 ... UTF8&psc=1
For steps 9-10, I couldn't get a 5 mm hole puncher, so I stuffed the holes with tissue and put tape over the holes. I also stuffed some tissues into the empty area shown in step 3 to lessen the impact from hits.
You might have to do some more modifications after testing (some of the rubber would make the kat parts too sensitive on mine, so I had to cut those pieces of rubber off), but if you're willing to do that, the results are very noticeable.
On another note, I haven't gotten my converter yet, but I can't wait to use it. I might make a video on it if I can properly record it and show the improvement in delay.
That actually helps quite a bit. I'll have to try out the style you were holding the sticks with, I was trying it the way people always do it in the arcade TnT. Maybe I can get mine as responsive as yours.Catgirl wrote:
yeah i've had people suggest i mod it, i'll definitely take a look c:
i already have a recording from today if you want to see the no delay https://twitch.tv/deconstream/v/80370278
i wouldn't recommend my style, i had no idea what i was doing cause i never played arcade before. i just tried a bunch of different ways and this is what felt rightToaKarn wrote:
That actually helps quite a bit. I'll have to try out the style you were holding the sticks with, I was trying it the way people always do it in the arcade TnT. Maybe I can get mine as responsive as yours.Catgirl wrote:
yeah i've had people suggest i mod it, i'll definitely take a look c:
i already have a recording from today if you want to see the no delay https://twitch.tv/deconstream/v/80370278
update: i modded my drum and here's an update of how responsive the dons are now. still working on the kats, i'll hopefully get them just as perfect really soon!
I have no idea how you're hitting those kats, I'm just assuming that you're shifting your finger over and the camera isn't fast enough.Catgirl wrote:
update: i modded my drum and here's an update of how responsive the dons are now. still working on the kats, i'll hopefully get them just as perfect really soon!
Now it's time to figure out how spinners and bouncing works, eh?I'm assuming you're using the guide from above; can I ask how much the mod cost you and where you bought everything from?
oh, it was relax mod so i hit everything as a don c:ToaKarn wrote:
I have no idea how you're hitting those kats, I'm just assuming that you're shifting your finger over and the camera isn't fast enough.Catgirl wrote:
update: i modded my drum and here's an update of how responsive the dons are now. still working on the kats, i'll hopefully get them just as perfect really soon!
I'm assuming you're using the guide from above; can I ask how much the mod cost you and where you bought everything from?
this was mainly just to show how responsive the drum itself was. i haven't modified any of the sensors for the rims yet. well i did, but i screwed them up so i reverted back to normal and i'll try them again tomorrow.
i used the exact guide you linked. the cork things cost me $7.99 for three + shipping, i managed to get some scrap rubber for free at home depot, and the rest of my shopping was buying a mini hole punch and some tape which probably cost me $3 total. it wasn't too bad at all, and the mod itself probably took me 2 hours. filling all of the holes with rubber takes more time than you'd think, plus i didn't really know exactly what i was doing.
just a warning, if you mod like this, you can't overlap the left and right side rim sensors with the rubber or both sides will be treated the same which can cause some problems. i also noticed there's a spot right in the middle of my drum that hits both dons at the same time, but that's super minor.
once i can perfect the sensors on the rims i'll update and let you know how it goes c:
Didn't know Relax did that, the description isn't very specific.Catgirl wrote:
i used the exact guide you linked. the cork things cost me $7.99 for three + shipping, i managed to get some scrap rubber for free at home depot, and the rest of my shopping was buying a mini hole punch and some tape which probably cost me $3 total. it wasn't too bad at all, and the mod itself probably took me 2 hours. filling all of the holes with rubber takes more time than you'd think, plus i didn't really know exactly what i was doing.
just a warning, if you mod like this, you can't overlap the left and right side rim sensors with the rubber or both sides will be treated the same which can cause some problems. i also noticed there's a spot right in the middle of my drum that hits both dons at the same time, but that's super minor.
once i can perfect the sensors on the rims i'll update and let you know how it goes c:
Look forward to the update!
Topic Starter
My drum has the same mods as the neogaf post - I made the mistake of covering everything with rubber and I often hit kats and dons at the same time which was a huge pain. I've since taken it apart again and left gaps around the edges and it's much better. Also remember to leave gaps for the kats too! I'm still double hitting some kats when I shouldn't be, I'll take it apart and fix it for good soon...
Is this still available for purchase? I am really interested in getting one.
Topic Starter
Yep! I have tons in stock, click here or the link in the first post.
I had another question; about how long does it take to ship to the US?
Topic Starter
About 1.5 weeks seems standard - express post unfortunately adds about $20 to the cost.
If you're unlucky it can take up to 3 weeks, but post to the US seems fairly consistent.
If you're unlucky it can take up to 3 weeks, but post to the US seems fairly consistent.
So I have kind of a weird setup. Basically none of my laptops/tablets are able to handle Osu efficiently, & I can't play near my PC. So my only choice is to connect my PC from 10 meters away to the big screen TV using hdmi & usb extension cables. I run the game at 720p to prevent screen tearing, & the speaker is in the same room so the sound is fine.
But then the input lag from the tatacon is quite noticeable during high bpm songs, due to the long distant usb cord. I can still hit the notes if I focus on the beats, but the Don/Kat sounds are really distracting because they play a bit late after the hit.
Do you guys have any ideas how to reduce the latency? I did some googling & some people suggest using a USB hub, but I'm not sure if that's gonna make a different
But then the input lag from the tatacon is quite noticeable during high bpm songs, due to the long distant usb cord. I can still hit the notes if I focus on the beats, but the Don/Kat sounds are really distracting because they play a bit late after the hit.
Do you guys have any ideas how to reduce the latency? I did some googling & some people suggest using a USB hub, but I'm not sure if that's gonna make a different
Topic Starter
Due to the nature of USB, it either works or it doesn't - there is no extra latency from a long USB cable (technically 30 nanoseconds, but that's about 100,000 times shorter than you can notice).
Is the audio coming through HDMI too? Some TVs can have atrocious input lag, and if it's handling the audio too it could explain it. If it's the audio, you may have to run a 3.5mm cable along with the rest
If that fails, try and look at the lights on the converter - see if they're also lagging. It could be the controller isn't sensitive enough and only registers a hit some time after you actually make it. I think this is unlikely as even bad controllers register hits on time, you just have to hit them really hard.
Good luck!
Is the audio coming through HDMI too? Some TVs can have atrocious input lag, and if it's handling the audio too it could explain it. If it's the audio, you may have to run a 3.5mm cable along with the rest
If that fails, try and look at the lights on the converter - see if they're also lagging. It could be the controller isn't sensitive enough and only registers a hit some time after you actually make it. I think this is unlikely as even bad controllers register hits on time, you just have to hit them really hard.
Good luck!
Nvm, after configuring the universal offset in Osu to -60, the hitsound is on point now
The only problem left is modding my tatacon for better sensitivity...
The only problem left is modding my tatacon for better sensitivity...